COMPATIBILITY

  • 2020+ CORVETTE COUPE, LT2

OVERVIEW

The catch can draws out oil and water condensation from the crankcase gasses that would otherwise be drawn into the intake manifold. This prevents oil buildup in the intake, intercooler system walls, throttle body, and intake manifold. This effectively raises the octane, can increase engine performance from cleaner inlet air, and can lower hydrocarbon emissions. The closed system prevents unwanted oil vapors from entering into the cabin. Catch can kits include everything needed for a complete installation.


FLUID LOCK® CATCH CANS

In 2022, Radium Engineering implemented a revolutionary design change to the 7 fluid ounce standard catch can. An inherent problem always existed with typical catch cans when not serviced regularly. The fluid contaminants will eventually leave the reservoir pouring into the air intake system causing poor engine performance. To resolve this issue, Radium created the Fluid Lock® Catch Can. This contains a patented mechanism that prevents the reservoir from overfilling and traps the collected fluids until it is emptied.


COLLECTION & EMPTYING

The rate the catch cans collect oil and moisture contaminants will vary from one individual vehicle to the next, so there is no set emptying interval. PCV catch cans tend to collect more than CCV catch cans. Check the level of the catch can using the integrated dipstick starting at 3-4 weeks of driving and repeat as needed to determine how often they should be emptied.

Catch cans can be emptied by unscrewing the lower reservoir and removing it from the vehicle to dump out, or in cases where there is available space under the catch can, the Petcock Drain Kit can be installed to drain them.

In cases where oil collection is excessive, an engine issue may need to be addressed. The reasons a catch can will collect an excess of oil include:

  • Excessive blowby from engine damage
  • Crankcase windage from an over-full oil level
  • Poor placement of breather ports and/or poor baffling inside breather ports
  • PCV valve not closing and leaking under heavy load

20-1385-FL CATCH CAN KIT, PCV, 2020+ CORVETTE COUPE, LT2, FLUID LOCK

The anodized aluminum catch can bracket mounts to the RH rear side of the engine bay using OEM threaded holes. It secures the catch can high enough to stay clear of the hot exhaust. It is compatible with the factory dry sump system.

The PCV catch can kit improves the performance of the LT2 crankcase ventilation system. A PCV valve is included making this kit compatible with all applications including turbocharging. The catch can runs inline between the provided PCV valve and the intake manifold. When the intake manifold pressure is close to or greater than atmospheric pressure, the PCV "check" valve closes and, thus, this hose experiences no flow. Conversely, the PCV hoses will experience "metered" vacuum when the engine is idling, steady state cruising, and decelerating. This would normally draw unwanted crankcase vapor, unspent fuel, and oil sludge into the intake manifold immediately after a high load run.

20-1386-FL DUAL CATCH CAN KIT, CCV, 2020+ CORVETTE COUPE, LT2, FLUID LOCK

The anodized aluminum catch can bracket mounts to the LH rear side of the engine bay using OEM threaded holes. It secures the catch can high enough to stay clear of the hot exhaust. It is compatible with the factory dry sump system.. 

The CCV catch can kit retains factory functionality. Both crankcase vent lines from the valve covers run into the catch can. A large single line routes to the intake system. 

At low loads, these catch cans experience atmospheric pressure. However, when the engine is at high load (WOT), these vents will experience high flow out of the crankcase. This would normally lead to oil and sludge accumulation in the air filter intake pipe.

20-1387-FL TRIPLE CATCH CAN KIT, 2020+ CORVETTE COUPE LT2, FLUID LOCK

This dual catch can kit includes both the PCV and CCV catch can kits for the ultimate in engine protection. 

SPECS & FEATURES

  • Direct fitment with no drilling required
  • Large 10AN ORB inlet and outlet ports
  • 4AN ORB drain port
  • 2-step oil separation baffling
  • O-ring sealed dipstick
  • 7 fluid ounce capacity
  • Patented Fluid Lock® system

INCLUDED

20-1385-FL CATCH CAN KIT, PCV, 2020+ CORVETTE COUPE, LT2, FLUID LOCK

  • Baffled oil catch can with integrated condenser and dipstick
  • Anodized aluminum mounting bracket
  • 10AN ORB PCV valve quick connect
  • SAE quick connect fittings
  • Stainless mounting hardware
  • 3/8" PCV rubber hose
  • Spring clamps

20-1386-FL CATCH CAN KIT, CCV, CORVETTE COUPE, LT2, FLUID LOCK

  • Baffled oil catch can with integrated condenser and dipstick
  • Anodized aluminum mounting bracket
  • SAE quick connect fittings
  • Stainless mounting hardware
  • 5/8" PCV rubber hose
  • 3/8" PCV rubber hose
  • Spring clamps

20-1387-FL DUAL CATCH CAN KIT, CORVETTE COUPE, LT2, FLUID LOCK

  • Baffled oil catch cans with integrated condenser and dipstick
  • Anodized aluminum mounting brackets
  • 10AN ORB PCV valve quick connect
  • SAE quick connect fittings
  • Stainless mounting hardware
  • 5/8" PCV rubber hose
  • 3/8" PCV rubber hose
  • Spring clamps

ADDITIONAL IMAGES

20-1385-FL installed 20-1385-FL installed
20-1386-FL installed 20-1386-FL installed
20-1387-FL RH View 20-1387-FL RH View
20-1387-FL LH View 20-1387-FL LH View

Catch Can Kits, 2020+ Corvette Coupe, LT2

Regular price
Sale price
$0.00
Regular price
Shipping calculated at checkout.

Install Instructions PDFs

Installation Instructions (PDF)



This product is SEMA certified 49-state legal

Click on the image to view the SEMA Garage Certificate of Compliance.